Sawing
My TS 55 Saw is making strange noises
The strange noise is caused by MMC electronics in the tachometer regulated speed control sending pow...
Can a dust bag be attached to the TS 55 REBQ plunge cut saw?
Yes, a dust bag (product number 500393 ) can be attached to the TS 55 REBQ plunge saw.To be able to ...
Can Festool saw blades be sharpened?
Yes, Festool saw blades can be sharpened.Festool does not sharpen blades in our technical/service de...
Why are the FSK guide rails not compatible with the TS 55 160 mm Plunge Cut Circular Saw and what is the difference?
The FSK guide rails are not compatible with the TS 55 160 mm plunge saws as their base plates are ...
What does the 1-6 speed setting on the TS 55R EBQ saw mean?
The TS 55R EBQ saw is rated 2000-5200 no load speed and is broken down into 6 speed settings:
1 = 2...
How far can I cut in 12mm material using TSC 55 160mm Cordless Circular Saw?
The total length cutting capacity in 12mm material of a TSC 55 160 mm Cordless Circular Saw is 50 m...
Is there a laser available for KS 88?
No, There are no lasers available for the KS 88. If you require a mitre saw with a laser, the KS 120...
How can I get the belt and boots for KAPEX trimming attachments?
The transportation belt with boots are included when you buy Left and Right trimming attachments tog...
Is there a different crown moulding stop for left and right side of KAPEX saw?
There is only one moulding stop taht attaches to the KAPEX. part number 494369 .Even though it's...
Does Festool have a TS 75 Hebel blade?
Festool does not have a blade that cuts Hebel products.The PCD blades are only designed to cut FC sh...
What is new on the KS 120 REB?
The highlights of the new KS120 REB are:
Expandable side fences - New position of the smart bevel (...
TS 55 V HKC 55. What are the differences?
The main differences between these two saws are:TS 55
Easier to plungeVariable speedProvides better ...
The cutting depth adjustment lever on my HK 85 will not move up or down. What can be done to get it to work?
If the lever has seized and will not move Festool advise that this cannot be remidied by the user. ...
Does the TS 55F work with the cross cut rail system?
No, the TS 55 is not compatible with FSK cross cut rails .
Can the TS 55 be fine-tuned if the blade isn't accurate?
Yes. The dial on top of the depth guage allows adjustment to zero the TS 55 blade accurately.
My new guide rail has a plastic cover sticking out and I will cut through it when I use my saw. Is that normal?
Yes. It is normal to cut through the splinter guard when you first use the guide rail.
Can 3rd party blades be used on Saw Stop?
Yes, as long ads the specs of the blade are the same same curve thickness and the same diameter.
...
My new TS 55 / TS 75 will not plunge to the full depth. Why?
Prior to your first cut using your new saw and guide-rail together, the splinter guard on the guide ...
Does the Transport Wheel fit the CS 50 as well as the CS 70?
No, the transport wheel (part number 488064) is for the CS 70 only. The newest version of the CS 50 ...
Does the KSC 60 bevel to the left and right side and by how much?
Yes, the KSC 60 bevels 46 degrees L and 47 degrees R.
Can TSC 55 blades be sharpened?
Yes, the blades can sharpened up to (approx) 6 times, adjust the cutting edge to 0 pointWatch the vi...
Can I run a TSC 55 on one 18V battery?
The TSC 55 can be run on one battery however this does limit speed options ( Idling speed (2x18V) 26...
Can after-market blades be used TKS 80 SawStop?
Only Festool blades are recommended to be used with TKS 80. If an after-market blade is used on the ...
How do I remove the blade from my KS 120 KAPEX?
There are directional arrows on the screw, to loosen the blade turn key clockwise and to tighten tur...
Can Luchs cement sheeting 210mm diamond blade be sharpened?
The PCD blades can’t be sharpened, to get a longer life from the PCD blade, use a slightly lower ...
Are the guide rail support pads on the baseplate for plunge saws replaceable?
Yes they are. Glide Pads #10679073 for TS 60K Glide Pads #200173 for all other Circular saws are ava...
Does the TS 75 or TS 55 circular saws have a blade that cuts Hebel?
There are 3rd party blades available with the correct centre bore (20mm for TS 55 and 30mm for TS 75...
Can the HK/HKC saws be used on the FS Guide Rail as well as the FSK Guide Rail?
Yes, the HK and HKC Saws can be used on both the FS and FSK Guide Rails .
Can I use the cross cut rails for every saw?
No, predominantly the cross cut guide rails are used with the HK saw range . The new TS 60 plunge s...
Can I use the Diamond blade for materials like timber or MDF?
No, Festool does not recommended this application. The blade is designed for use only with cement-bo...
My KS 120 is losing power mid cut and only running 5-10% speed- what's happening?
The KS 120 REB has thermal protection built in, if the motor temp is too high it will go into a the...
Can the TS 55 F be used with the cross cut rail?
No, the base plate does not have the second groove to enable the saw to fit corly on the rail, howev...
When setting the depth of cut on my plunge saw there are two indication points - one is blank and one says FS - which one should I be using?
You should use the FS indicator (pictured right) when using the FS Guide Rails, otherwise use the bl...
Can I use the TS/HK tool dust catch bag when cutting aluminium?
The bag is designed for wood dust only, so there is a chance the aluminium may damage it or the bits...
The cartridge on my TKS 80 was triggered, can I use the saw without the SawStop cartridge until I buy a new one?
The TKS 80 saw cannot be used without the SawStop cartridge.ttps://www.festool.com.au/replacement-s...
What is the bed height of a KS 120 KAPEX 260mm Slide Compound Mitre Saw?
The KS120 has a bed height of 108mm.
How do I remove the blade from my KS 120 KAPEX?
To change the blade on the KS 120 is fast and easy.First, ensure paower to the saw has been disconne...
My KS 88/120 is making a strange noise when not under load, does it need to be serviced?
The strange noise is caused by the electronics in the tachometer regulated speed control sending pow...
Can the saw blade on my TS 55 and TS 60 K be calibrated after it has been sharpened?
The TS saws (TS 55 and TS 60 K ) can be adjusted so the 0 point is accurate but no other adjustment...
Will the dust cover (part number 577341) for the TS 55 fit on the HK 55?
They are compatible however you will need these spare parts and order via a retailer ;
Hex bolt 40...
Do Festool circular saws have replaceable adjustment cams (Glide Pads) on the baseplate?
Glide Pads (part number 10679073) for TS 60K Glide Pads and (part number 200173) for all other Circu...
What is the difference between the KS 120 EB and the KS 120 REB?
The R stands for relaunch. here is a summary of improvements:
A new base with integrated sliding tab...
Can I get a Festool bag for my FS 1900 /2400 guide rail?
There is only a bag for the FS 1400 guide rail, the FS Guide Rails Bag, see the details here :See al...
Can I use an ATF 55 on current FS rails?
Yes you can. All Festool plunge saws from ATF 55 models through to exisiting models will fit on pre...
Can I use the TKS 80 SawStop Saw without the SawStop cartridge?
No, the SawStop feature of the TSK 80 is a vital safety feature of the saw so you will not be able t...
Which guide rail(s) can the TS 60K Plunge Cut Saw go on?
The TS 60K Plunge Cut Saw will fit on both the FS Guide Rails and the FSK Guide RailsTo see how Fes...
My KAPEX leaks a bit of oil when it has been sitting for a while, should I be concerned?
There is a small allowance for oil that has seperated from the grease while the saw is not in use an...
On the TS 75 Circular Saw, is the protective material inside the Counter Flange and the Clamping Flange available as spare parts and replaceable?
Yes, the Clamping Flange (part number 492217) and the Counter Flange (part number 492216) are availa...
The guard on the KS 120 is not retracting correctly, what can be done to fix it?
To try and remmedy the non-retracting blade, follow these steps:
Disconnect the power or remove the ...
The laser on my Kapex seems dull, is something wrong?
The screw right hand side of the laser can be loosened and the laser lens removed. The lens can then...
Can the protective material on the inside of the TS 75's blade flanges be replaced?
The Clamping Flange and the Counter Flange are available as spare parts however the protective mater...
The guard is jammed on my mitre saw. How do I fix it?
Firstly, disconnect the power, remove the blade and find the material jamming the guard up through t...
Does the new TS 60 K connect on to the FSK rails the same way as a HK 55 does?
Yes, they attach, lock-in and are removed in the same way. For more information see the product page...
How many cuts can you make with the KSC 60?
There are many variables when it comes to measuring this but we have run tests and can advise that 2...
How to calibrate a TS 55 / TS 75 on a FS rail ?
Festool saws can be calibrated to the rail by adjusting the green cams on the base plate. Adjusting ...
Do I have to use dust extraction with the HK/HKC Saw?
No, it is not necessary to use dust extraction with the HK/HKC saw but for health and safety reason...
Can I sharpen my HK/HKC Saw Blades?
Yes you can have your blades sharpened. Should you need to purchase a new blade you can see our full...
Can I use the TSC 55K with one battery?
Yes, you can use the TSC 55K with one battery, when doing so the single battery must be placed in th...
My KS guard is not retracting correctly, what can I do?
If the guard on the KS (Slide Compound Mitre Saw) is not retracting correctly it could be that some ...
Can I join my older guide rail to the current FS rails?
No they are not compatible to join.
See the full range of compatible and "joinable" gui...
Can the TS 60K be used on the FS and FSk Guide Rail?
Yes, the TS 60K and the TSV 60K can be used on all guiderails in the Festool range.
What size roller does the PF 1200 come with and which V- Groove cutting wheel?
The PF 1200 comes with an A4 feeler roller and the V-grooving 90 degree blade.
Do TS 60 plunge saw blades fit the CSC 50 cordless table saw?
Yes.The TS 60K plunge saw blades will fit on both the TSV 60K and the CSC SYS 50 saws.For the ful...
What batteries will the CSC SYS 50 take?
The CSC SYS 50 Cordless table saw will take any battery over 4.0Ah.To see the full range of availabl...
Do the batteries in the CSC SYS 50 need to be the same Ah?
No, they do not need to be the same Ah, as long as both batteries are 4.0Ah or above they will work....
Can the CSC SYS 50 be plugged in to power as well as run on batteries?
No, the CSC SYS 50 runs on battery power only. There is no facility to plug the saw into mains power...
Can I run the CSC SYS 50 on one battery only?
No, the saw requires two batteries of 4Ah or more to operate.For the full range of Festool batteries...
Do you need the same screws for part number 491469 Parallel Side fence in order to use the dust cover 577341?
Yes, you will need the same screws for the dust cover for the TS 55 range.
Can the pre scoring blade that is on the new TSV 60K be retrofitted on to the TS 60K?
No, the TSV 60K is a completely new model with many different and unique parts which means the scor...
REVIEW Will the Insulation Saw ISC 240 18V 240mm cut hemp insulation?
Yes it will. For more information on the Festool Insulation Saw click here:
What is the best blade for cutting composite decking boards?
The best results when cutting composite decking boards will come from using a Fine Tooth Saw Blade.F...
How do I fit or remove riving knife and blade guard on my CSC SYS 50?
To remove, put the blade in the park position, turn off the saw. Using the allen key supplied, push ...
Does the PRECISIO Sliding 830mm Extension Table for CS 50 work on the CMS-GE router table?
Yes it does! The extension table is available here:
Can I use my 50mm hose with a Kapex?
No. The KAPEX will only take a 27mm internally or a 36mm externally on the outlet.For teh full range...
Which 160mm blade can you use for soft plastics?
Depending on cut quality all the timber blades can be used to cut plastics. For the best cut quality...
Does the TSV 60 needs to be aligned before you begin using
Yes, the TSV 60 should be aligned before use to ensure accurate cuts and correct depth. For a guide ...
Can I sharpen the scribing knife on my TSV 60?
No, this item would need to be re-purchased - item number is 577082
Why does the TSV 60 have a green plug-it cable?
The green Plug-It cable is for extra heavy-duty protection against damage due to sharp edges.
Can the RSC 18 saw take non Festool blades?
Yes, the RSC 18 saw uses a standard fitting so other blades are compatible.
Can you adjust the pendulum stroke?
Yes, set for minimum for metal, maximum for materials like wood.
Can you remove the guide for close access on the RSC 18 saw ?
Yes, you can remove the guide for close access when required.
Can you get the dust extraction accessory separate for the RSC 18 saw ?
Yes. the dust extraction adapter is vailable seperately. The part number is 577074.
Can you use one battery, or any battery, on the KSC 60?
The KSC 60 EB operates on one or two 4 Ah or higher batteries . With only one battery installed you...
Can you use blades upside down in the RSC 18 saw?
Yes. Blades can be fitted upside down in the RSC18.
Can I use the RSC18 reciprocating saw on the same setting for all materials?
No - its recommended to use the minimum setting for metal material and maximum for wooden material.
What is the cutting height on the TKS 80?
The cutting height of the TKS 80 SawStop 254mm Table Saw at 90/45 degrees is 80/56mm.
Can the RSC Reciprocating Saw be used on concrete?
The RSC 18 18V Cordless Reciprocating Saw is designed for use with wood/steel/plastic/plasterboard a...
Can I use dust extraction when cutting aluminium with my KS120/88/60 or TS 55/60/75?
Yes. Dust extraction can be used when cutting aluminium.
Can I set the blade depth on the TS 55 saw and cut without plunging?
No, as there is no blade guard on the TS 55 range it is not possible. The HK range of saws do have ...
What capacity is attainable when using the 575827 TKS 80 with sliding table?
A 920mm cross cut can be achieved with the SawStop Sliding 920mm Extension Tables
Why does the TSV 60K Plunge Cut Scoring Saw come with a 1900mm rail and not the standard 1400mm?
As the saw is longer than the others in our range due to the pre score function, the 1900mm rail giv...
Can the TS 75 cut melamine 70mm deep?
Yes - the TS 75 210mm Plunge Cut Circular Saw cutting depth is 0mm - 75mm (at 45 degrees the depth ...
How many CSC SYS 50 favorites can be set?
The CSC SYS 50 can have 4 favourite cuts set. See this link https://www.festool.com.au/csc-sys-50-1...
Will the fast fix adjustable clamp fit into the channel of the new CSC-SYS 50 saw
Yes.The Fast Fix Adjustable Clamp is a great method of holding materials in place while processing...
Can the universal saw blade that comes with the CS 50 (part number 492048) be used with the TS 55 circular saw?
No, the Universal Saw Blade (part number 492048) cannot be used on the TS 55 Plunge Saw, the size a...
Can I buy a CMS table or module to suit my TS55 or OF 1400 ?
The CMS system was discontinued in 2018. We have no tables or modules available for purchase.
Can the Fein Slugger Saw cut 50mm of Chrome Coated Steel?
Yes it can, using the 14" (355mm) saw blade stainless steel (part number 63502014620 90 tooth.
Can I fit a dust bag to my old TS 55 or new TS 60?
Yes, the Dust Catch Bag for TSC 55 & HKC 55 (part number 500393) is compatible with all TS 55/6...
Can I use the 8.0Ah battery with my HKC 55?
Yes, although the 8.0Ah battery is bigger than most it won't effect the function of the HKC 55 ....
How do I fit the Dust Catch Bag (500393) to my TS 55 or HKC?
Remove the angle piece from the dust port on your TS 55 or HKC 55 and fit the Dust Bag over the o...
Is using the Dust Catch Bag on my TS 55 or HKC as efficient as using them with dust extration?
A Dust Catch Bag is efficient to 90%, compared with 95% for Dust Extraction (using an attached Dust ...
Can I run my KSC 60 on non Bluetooth batteries?
Yes. Provided they are 4Ah and over 18V. Please note that if non-Bluetooth batteries are used, a Blu...
Can I use the PF 1200 V Grooving bit 90 Deg on my TS 55?
You cannot use the V Grooving bit on your TS 55, unfortunately it will not fit on the saw (H x W - ...
Do the blades for the TS 55 and TSC 55 also fit the HK 55/HKC 55?
The early versions of the TS55, TSC55 160mm Plunge Cut Saws were delivered with 2.2mm thick blades ...
Is there a diamond blade for the TS75 available?
Yes, there is a diamond blade for the TS 75 210mm Plunge Cut Circular Saw saw see link: https://www...
Does the Bluetooth on a Festool vacuum connect to the CSC 50 tool, or does one of the batteries need to be Bluetooth?
To use the Bluetooth feature from the dust extractors to Festool tools at least one of the batteries...
Should I get a Plunge Saw or a Circular Saw? What is the difference?
Check out our comparison page between Plunge Saws and Circular Saws here:
I have lost the screws that hold my KS 60 Kapex to the trolley base, how can I get replacements?
You can order the spare parts below from your Festool Dealer - each saw and base requires 4 of each ...
Does the TSV 60K Plunge Cut Scoring Saw come in a cordless version?
There are no current plans for this to be released in a cordless version
I bought the CSC SYS 50 Cordless 168mm Systainer Saw and would like to buy the table?
The Systainer Saw Mobile Underframe is available to purchase #577001
My CSC 50 trolley wheels are running rough and is some cases seizing, how do I fix this problem?
Please remove the cap from the CSC 50 trolley wheels and spray some grease into the hub area you ca...
What material is my TKS 80 table top made of? Is it aluminum?
The tabletop and the portals of the TKS 80 are made of magnesium through-cast.
Can I sharpen my F28219 210mm saw blade?
The PCD blades can’t be sharpened. To get longer life from the PCD blade, slightly slower speeds...
Which saw blades are for which application?
Festool Saw Blades are identified by a coloured ring around the central arbor. The colour of the rin...
How do I use the Parallel Side fence for Festool Saws?
See the video below for a guide on how to use the parallel side fence for a Festool Saw
Which Parallel fence guide suit which saws?
The 491469 parallel Side Fence is suitable for the TS 55, and the 576912 parallel side fence ...
When cutting with a Festool Circular or Plunge Saw what speed should be use?
This will depend on the application - see the chart below for an indication of speeds/application
How can I care for my plunge saw? What can I do ensure longevity of my tool?
THE IMPORTANCE OF ONGOING PLUNGE SAW MAINTENANCE
When we discuss maintenance, we refer to the care...
I've heard the KS 120 REB is 1600 watts, but they have a soft start. How much watts do they draw with no load or light load?
They run around 700W to 800W at no load, full speed, and anything up to 1600W depending how hard you...
Can I use the ISC 240 saw for repetitive cutting?
Yes, with the guide rail and angle stop. Repeat cuts can be made perfectly straight and with precise...
Can I use my adjustable angle stop on the new CSC SYS 50?
No, the design for the adjustable angle stop is very different for the new CSC SYS 50. It sits ve...
Does the KS 120R have a double laser light to assist with cutting?
Yes, it has a double laser line for precise saw cutting.
What materials can you use the HK 85 groove attachment?
Wood or plastic can be milled with the HK85 groove attachment.
Can I use my smart bevel for my KS 60 for external angles or internal only?
The smart bevel can transfer angles to the KS 60 and KS 120 sliding compound mitre saw. Using the be...
I have a PF 1200, do I need a V groove cutter for 90 degree cuts?.
Festool have the V - Groove cutter HW SW D18/A90 for this application.
I need to replace the dust extraction nozzle on my RSC 18 Reciprocating Saw?
The replacement part number is #577074
What speed should I run my Festool TS 55/65 on different materials and blades?
As the chart in user manual indicates, use the correct blade and these speed ranges for each type of...
Can I use 1 x 5.0Ah and 1 x 5.2Ah battery with either of my TSC 55 or a CSC SYS saws?
Yes, both the 5.0Ah and 1 x 5.2Ah batteries can be used in combination on the TSC 55 or the CSC SYS...
Can I use a HK saw on a normal FS guide rail?
Yes! Though the HK really shines for cross-cuts with the FSK Guide Rails.
Festool abbreviations - What does the 'K' mean in the plunge saws?
K stands for the kick back stop feature.
What's the difference between KS 120 laser guide, and KS 60 light led guide?
The KS 120 has 2 laser lines, showing the user the outer lines of where the blade will cut.The KS 60...
Is there a special Festool stop/clamp for short lengths (100-180mm) repeating cuts on my KS 60?
No there is no stop or clamp for this. Festool does not offer a stop for this application.
Can I use the new SYMC 70 to cut aluminium?
Yes you can by purchasing the Aluminium Saw Blade 210mm x 2.3mm x 30mm 64 Tooth
Can I use the double extraction for the new SYMC 70 saw?
Yes you can, by using the Y Piece connector for dual suction hoses.
Can I use the side extensions (part no. 201909) on a KS 60, without the mobile trolley? Can I use the extensions on the ground, or work bench,with extension legs folded?
This is an option, however you must also use the adapter plate (part no. 202056) and the extensions ...
Categories