Saws - Your Questions Answered

Blades

Can I use the Diamond blade for materials like timber or MDF?

No, Festool does not recommended this application. The blade is designed for use only with cement-bonded and gypsum-bonded chipboard and fibreboard. The tooth design combined with low number of teeth means there will be problems damaging the material or blade when cutting timber or MDF.

Can Luchs cement sheeting 210mm diamond blade be sharpened?

The PCD blades can't be sharpened, to get a longer life from the PCD blade, use a slightly lower variable speed.

Can Festool saw blades be sharpened?

Yes, Festool saw blades can be sharpened. Festool does not sharpen blades in our technical/service department.

Can I sharpen my F28219 210mm saw blade?

The PCD blades can't be sharpened. To get longer life from the PCD blade, slightly slower speeds and feed-rate are required.

Which saw blades are for which application?

Festool Saw Blades are identified by a coloured ring around the central arbor. The colour of the ring represents the material for which the saw blade is most suited

What is the best blade for cutting composite decking boards?

The best results when cutting composite decking boards will come from using a Fine Tooth Saw Blade.

What Blades work on your oscillating tools?

Festool Vecturo and Fein SuperCut blades, Oscillating tools Festool VECTURO (OS 400) and Fein SuperCut (FSC/AFSC) take the same type of blades, which won't fit on any other Oscillating tools, such as MultiMaster (FMM), MultiTalent (FMT) or any Starlock tools (models ending with QSL) and there is no adaptor which will allow for these tools to take SuperCut blades. The only current models that can take supercut blades are: Fein FCS1.7Q, AFSC1.7Q and Festool OS400 but if you would like to put Starlock blades (including Starlock Plus and Starlock Max) onto Vecturo or Supercut QuickIn version, you can do it using an adapter, p/n 35222952050, for Supercuts withought Quick In, p/n for the adaptor is 35222952040

Which 160mm blade can you use for soft plastics?

Depending on cut quality all the timber blades can be used to cut plastics. For the best cut quality the Laminate Saw Blade 160mm x 1.8mm x 20mm 52 Tooth (part number 205554) can also be used.

CSC SYS / CS

Can I run the CSC SYS 50 on one battery only?

No, the saw requires two batteries of 4Ah or more to operate.

Can I use my adjustable angle stop on the new CSC SYS 50?

No, the design for the adjustable angle stop is very different for the new CSC SYS 50​. It sits very differently on the machine. Â

Does the PRECISIO Sliding 830mm Extension Table for CS 50 work on the CMS-GE router table?

Yes it does! The extension table is 492100

Does the Transport Wheel fit the CS 50 as well as the CS 70?

No, the transport wheel (part number 488064) is for the CS 70 only. The newest version of the CS 50 has integrated wheels that can fit to the older version - you would need to buy the complete set - part number 10030845.

How do I fit or remove riving knife and blade guard on my CSC SYS 50?

To remove, put the blade in the park position, turn off the saw. Using the allen key supplied, push through the hole under the FESTOOL logo and lift the riving knife/blade cover. To install, push the riving knife/blade through the gap until it clicks into place.

How many CSC SYS 50 favorites can be set?

The CSC SYS 50 can have 4 favourite cuts set.

What is the part number for CS 70 EB filter?

The CS 70 EB filter part number is 447995.

What's the part number for the push stick for CMS TS 55?

Part number for the work piece holder for table saws and also CMS table set up is p/n 450199.

Do TS 60 plunge saw blades fit the CSC 50 cordless table saw?

Yes.The TS 60K plunge saw blades will fit on both the TSV 60K and the CSC SYS 50 saws.

I bought the CSC SYS 50 Cordless 168mm Systainer Saw and would like to buy the table?

The Systainer Saw Mobile Underframe is available to purchase #577001 Â

Will the fast fix adjustable clamp fit into the channel of the new CSC-SYS 50 saw?

yes

Do the batteries in the CSC SYS 50 need to be the same Ah?

No, they do not need to be the same Ah, as long as both batteries are 4.0Ah or above they will work. e.g 1 x 4.0Ah and 1 x 5.2Ah

My CSC 50 trolley wheels are running rough and is some cases seizing, how do I fix this problem?

Please remove the cap from the CSC 50 trolley wheels and spray some grease into the hub area you can use WD-40 300G specialist high performance white lithium grease found in Bunnings

My CSC 50 trolley wheels are seizing, what can be done?

Remove the plastic cap (with the Festool logo on it) on CSC 50 Underframe and spray some grease into the hub area where the screw is located - we recommend you use WD-40 specialist high performance white lithium grease - you can purchase this from Bunnings Australia. Â

What batteries will the CSC SYS 50 take?

The CSC SYS 50 Cordless table saw will take any battery over 4.0Ah.

HK/HKC Saws

Can I sharpen my HK/HKC Saw Blades?

Yes you can have your blades sharpened. Should you need to purchase a new blade you can

Can I use a HK saw on a normal FS guide rail?

Yes! Though the HK really shines for cross-cuts with the FSK Guide Rails

Can the HK/HKC saws be used on the FS Guide Rail as well as the FSK Guide Rail?

Yes, the HK and HKC Saws can be used on both the FS and FSK Guide RailsÂ

Do I have to use dust extraction with the HK/HKC Saw?

No, it is not necessary to use dust extraction with the HK/HKC saw but for health and safety reasons and for a clean job site, it it is advisable. You can attach the saw to an appropriate dust extractor or you can attach the the optional Dust Catch Bag, part number 500393

Can I use the 8.0Ah battery with my HKC 55?

Yes, although the 8.0Ah battery is bigger than most it won't effect the function of the HKC 55

What materials can you use the HK 85 groove attachment?

Wood or plastic can be milled with the HK85 groove attachment

Will the dust cover (part number 577341) for the TS 55 fit on the HK 55?

They are compatible however you will need these spare parts and order via a retailer - Hex bolt 402234 - Compression spring 444754 - Clamp 10012382 - Thumb nut 440712 Â

The cutting depth adjustment lever on my HK 85 will not move up or down.

What can be done to get it to work? If the lever has seized and will not move Festool advise that this cannot be remidied by the user. Please contact the Festool Repairs Centre to arrange a repair to your tool.

What is the total width of timber you can cut with each HKC rail (250, 420, 670)?

It depends on the thickness of the material. Refer to HKC 55 presentation - slide 3. M:\09 Training\23. Product in Focus

Festool abbreviations - What does the 'K' mean in the plunge saws?

K stands for the kick back stop feature.

ISC Insulation Saws

Can I use the ISC 240 saw for repetitive cutting?

Yes, with the guide rail and angle stop. Repeat cuts can be made perfectly straight and with precise angles. Guide Rail Mitre Guide for ISC 240 ISC 240 18V 240mm Cordless Insulation Saw

REVIEW Will the Insulation Saw ISC 240 18V 240mm cut hemp insulation?

Yes it will.

Jigsaws

Will Festool jigsaw blades fit a Festo PS-1 / PS-2?

Can the tool be adjusted to fit the Festool blades?All bayonet blades on the market will fit and they are held in place with a screw. The teeth supporting the blade will need to be adjusted.

Are CARVEX jigsaw accessories such as base plates compatible with the TRION jigaws?

No, CARVEX accessories are not compatible with TRION jigsaws.

How do I change the splinterguard on the Carvex PS 42/ PSC 420?

Replace the splinterguard by removing the old one and partially inserting the new one until it touches the blade - turn on the jigsaw and press the splinterguard towards the blade for splinter free cutting. For more information on the CARVEX Jigsaw splintergurad watch the short video below:

Can I turn off the strobe light on my jigsaw?

Yes, the strobe light can be turned off. There are three options. Light Flashing - Light with Strobe Light On - Light without Strobe Light Off - Light switched Off

Can the strobe lights on Festool jigsaws be turned off?

Yes it can. There are three options.Light Flashing - Light with Strobe - Light On - Light without Strobe - Light Off - Light switched Off

Do I need to use a base plate for the circle cutter attachment on jigsaw?

Yes you have to use the jigsaw adapter base plate for precise circular cuts

Is there a centering pin that comes with the circle cutter for jigsaws or is it available for purchase?

The centering pin comes with the unit at the time of purchase.

What is the strobe light on my jigsaw for?

The advantage of using a strobe light is that it gives the illusion the blade stands still and can make it easier to follow your cut line. The strobe will adjust depending on the speed of the blade to give this illusion.

What setting does my jigsaw need to be set to for under cuts?

Make sure the jigsaw is set at 3 for undercuts.

KS KAPEX Saws

How many cuts can you make with the KSC 60?

There are many variables when it comes to measuring this but we have run tests and can advise that 205 cuts were acheived on 45 x 190mm MPA 10 pine using 2 x 5.2Ah batteries. Please keep in mind that some of the variables include: the type of blade used the speed of cut the density of the material moisture content of the material sharpness of the blade

Is there a laser available for KS 88?

No, There are no lasers available for the KS 88. If you require a mitre saw with a laser, the KS 120 has a laser or the KS 60 is equipped with an LED light.

Is there a special Festool stop/clamp for short lengths (100-180mm) repeating cuts on my KS 60?

No there is no stop or clamp for this. Festool does not offer a stop for this application.

Can I use the CT 15L (577414) with my Kapex Saw?

You can use the CT 15 however we do recommend you buy an antistatic hose with D36 connector to allow for more volume of dust to be extracted. Depending on wattage of the tool, the CT15 has a maximum connected load of 1200 watts so if placed under load may trip the circuit breaker in the extractor. To overcome this the tool would need to be operated off a separate circuit.

Does the bevel angle adjustment come with the Kapex 260 mm Slide Compound Mitre Saw KS 88 E?

No, not with the Kapex KS 88 E. The bevel angle adjustment comes only with the Kapex KS 120 EB 260 mm Slide Compound Mitre Saw.

Is there a different crown moulding stop for left and right side of KAPEX saw?

There is only one moulding stop taht attaches to the KAPEX. part number 494369 . Even though it's design is not symmetrical, it is suitable for both left and right side of KAPEX KS 120 or KS 88 . There is a crown molding stop available for the trimming attachments.

What are the differences between a Kapex KS 88 E and Kapex 120 EB 260 mm Slide Compound Mitre Saw?

Kapex KS 88 E does not have the following compared to the KS120,No Laser, No fine adjustment, No smart bevel cannot cut 120mm(No special cut position, Does not hold its own head weight) Does not hold its head weight when not locked.

What do I do if the laser on my KAPEX saw does not align with the blade?

The adjustment of the laser on your Kapex 120 can be adjusted by the user but it is quite complicated. We recommend taking it into a repair agent for calibration and laser adjustment for the optimal performance of your Festool machine. Your local repair agent can be located via our websites

What is the bed height of a KS 120 KAPEX 260mm Slide Compound Mitre Saw?

The KS120 has a bed height of 108mm.

Can I run my KSC 60 on non Bluetooth batteries?

Yes. Provided they are 4Ah and over 18V. Please note that if non-Bluetooth batteries are used, a Bluetooth enabled Dust Extractor cannot be linked via the Bluetooth function, the Dust Extractor would need to operated manually or alternatively, use a Dust Catch Bag

Can I use my 50mm hose with a Kapex?

No. The KAPEX will only take a 27mm internally or a 36mm externally on the outlet.

Can you use one battery, or any battery, on the KSC 60?

The KSC 60 EB operates on one or two 4 Ah or higher batteries. With only one battery installed you'll get a maximum blade speed of 1,800 RPM. With two batteries speed increases to 3,500 RPM.

Does the KS 120R have a double laser light to assist with cutting?

Yes, it has a double laser line for precise saw cutting.

Does the KSC 60 bevel to the left and right side and by how much?

Yes, the KSC 60 bevels 46 degrees L and 47 degrees R.

How do I remove the blade from my KS 120 KAPEX?

There are directional arrows on the screw, to loosen the blade turn key clockwise and to tighten turn anti clockwise.

I have lost the screws that hold my KS 60 Kapex to the trolley base, how can I get replacements?

You can order the spare parts below from your Festool Dealer - each saw and base requires 4 of each of the following: (Part number: 10027790) Cheese Head screw (Part number) 10025021 Washer

I've heard the KS 120 REB is 1600 watts, but they have a soft start.

How much watts do they draw with no load or light load? They run around 700W to 800W at no load, full speed, and anything up to 1600W depending how hard you push it through the timber. With a good sharp blade, soft pine and slow feed rate draw is approx 900W to 1000W.

KS 120 Scales for Left and Right Trimming Attachment - Fixed and Sliding The drawing shows 2 part numbers for each side and it is unclear which is sliding and which is fixed - they are as follows - 479748 - Fixed Scale for Left side - 479749 - Sliding Scale for Left side - 479211 - Fixed Scale for Right side - 479806 - Fixed Scale for right side My KAPEX leaks a bit of oil when it has been sitting for a while, should I be concerned?

There is a small allowance for oil that has seperated from the grease while the saw is not in use and has rested for a while, once you start using it again this will stop. If you are still concerned please book your Kapex in for Service at your nearest Festool Dealer or through the Festool Repairs Centre

My KS 120 is losing power mid cut and only running 5-10% speed- what's happening?

The KS 120 REB has thermal protection built in, if the motor temp is too high it will go into a thermal protection mode. In this mode the tool can still be turned on but it will be running at a reduced RPM to cool the motor, the saw will reset to normal once the motor has cooled down. Ensure the saw blade is the appropriate choice for the material you are cutting and the blade is in good condition.

My KS 88/120 is making a strange noise when not under load, does it need to be serviced?

The strange noise is caused by the electronics in the tachometer regulated speed control sending power to the motor in a stream of 'pulses'. The motor is constantly being turned on and off in order to keep the saw blade rotating at a constant speed, most of the sound is being produced by gear backlash this is a normal function with this tool.

My KS guard is not retracting correctly, what can I do?

If the guard on the KS (Slide Compound Mitre Saw) is not retracting correctly it could be that some material may have lodged into the blade area while cutting, please follow these steps to check. disconnect power, or remove batteries. remove blade ( clockwise to loosen KS blade bolts) inspect inside guard cover for any debris which may be lodged preventing smooth operation. Reinstall blade , counter clockwise to tighten firmly If unable to remedy - take KS to an authorised repairer or drop off location SEE ALSO: The guard on the KS 120 is not retracting correctly, what can be done to fix it?

What are the advantages of the KS 60 KAPEX (561695) over the KS 60 KAPEX (561687)?

The advantages of the KS 60 KAPEX (561695) over the KS 60 KAPEX (561687) is that the set also includes the following features: Smart Bevel (494370) Adapter Feet (500121) LED Spotlight - Aside from these added features both models are the same.

What is new on the KS 120 REB?

The highlights of the KS120 REB are: Expandable side fences - New position of the smart bevel (at the back of the saw, like in KS 60 model ) Cleantec new type dust attachment for better connection with Dust Extractor.

What is the difference between the KS 120 EB and the KS 120 REB?

The R stands for relaunch. here is a summary of improvements: A new base with integrated sliding table extensions that provide even greater work surface area for material support. The new base is still compatible with existing Kapex accessories including the Kapex Crown Stops, UG, and UG Extensions. The bayonet-style dust port allows a positive connection with the latest generation of Cleantec hoses for superior dust collection. The saws motor structure has been improved for longer increase service life.

What's the difference between KS 120 laser guide, and KS 60 light led guide?

The KS 120 has 2 laser lines, showing the user the outer lines of where the blade will cut. The KS 60 has a shadow line, showing where the blade will cut.

Why is the laser on my KS 120 Kapex dim and/or blurry when in use?

To remove and clean the laser window on the KS 120 firstly unscrew window holder screw 2-3 turns. Press front of window into machine to release the plastic tabs. Slide window out of head. Clean the window or replace if necessary. See page 30 of the KS 120 KAPEX manual for more information.

Can I use the side extensions (part no. 201909) on a KS 60, without the mobile trolley?

Can I use the extensions on the ground, or work bench, with extension legs folded? This is an option, however you must also use the adapter plate (part no. 202056) and the extensions will not be level immediately. You will need to support the extensions with timber or suitable material to ensure its level. There is the ability to screw a support piece under the extension.

How can I get the belt and boots for KAPEX trimming attachments?

The transportation belt with boots are included when you buy Left and Right trimming attachments together as a set. They are also included in the KAPEX set (when bought together with the mobile trolley and both trimming attachments). If you would like to purchase them separately, you need to get the boots and the belt separately as spare parts. Part numbers are the same for all KS models:Belt: 700549 Protective cap (single): 700176

The guard on the KS 120 is not retracting correctly, what can be done to fix it?

To try and remmedy the non-retracting blade, follow these steps: Disconnect the power or remove the batteries. Remove the blade (clockwise to loosen KS blade bolts) Inspect the inside guard cover for any debris which may be lodged preventing smooth operation. Reinstall blade, counter clockwise to tighten firmly if unable to remedy Take KS to an authorised repairer or drop off location

The laser on my Kapex seems dull, is something wrong?

The screw right hand side of the laser can be loosened and the laser lens removed. The lens can then be cleaned, this will ensure the laser is bright and clear.

Does the new Dust Catcher Bag for the KSC 60 (and KS 60 and KS 120) suit the TS 55R & TS 55F range?

No the new Dust catcher Part No.577173 doesn't fit the TS 55 range The part number for the TS & HK range dust bag is 500393

Can a laser be fitted to the KS 88 instead of purchasing the KS 120?

KS 88 Lasers CAN be retrofitted but it is not economical to do so. Although all the switching and electronics are included in the KS 88 module (identical to the KS 120 ), there are no mounting points for the laser modules. These mounting points are part of the KS 120Â gearbox housing, therefore it must also be replaced and the total conversion cost exceeds $900.

Can I use my smart bevel for my KS 60 for external angles or internal only?

The smart bevel can transfer angles to the KS 60 and KS 120 sliding compound mitre saw. Using the bevel for both internal and external angles. No calculations are needed.

Can any combination of 4ah/5.0/5.2/6.2/8ah batteries be used in a dual battery tool saw, ie KSC 60/TS55/60 or CSC50.

Yes, but please note, once the lower Ah battery is drained, the speed option is reduced, before the larger capacity is drained also.

Other

Do Festool circular saws have replaceable adjustment cams (Glide Pads) on the baseplate?

Glide Pads (part number 10679073) for TS 60K Glide Pads and (part number 200173) for all other Circular saws are available to order online or through your closest Festool Dealer.

Does the Pizza Saw really cut pizza?

Yes it does and, it cuts pizza very well! For the Pizza Cutter and other Festool promtional items, please see the Festool Fan shop

How do clean my TS pizza cutter!

Carefully remove the blade by grabbing it and pulling down from the pizza saw. Bon appetit!

How to cut "Speed Panel"?

Best option is the HK 85 with a 230 mm diamond blade together with a guide rail an dust extractor

EDITED Do I need a splinter guard when cutting aluminium?

splinterguard is not needed for aluminium other than giving the cut line. The tooth design of different blades may alter the splinterguard even though both 1.8mm (so if FS used for wood normally may impact). Bonus tip! Ensure Aluminium is supported underneath ie: mdf/foam to help achieve clean cuts!

How can I care for my plunge saw?

What can I do ensure longevity of my tool? THE IMPORTANCE OF ONGOING PLUNGE SAW MAINTENANCE When we discuss maintenance, we refer to the care taken to keep your saw in good working order, from cleaning it and sharpening the blade to changing the motor brushes and more; these practices all have the cumulative effect of extending your plunge saw's lifespan. These easy steps will help keep your tool running smoothly while working safely and efficiently and achieving professional results. Keep Your Plunge Saw Clean Dust and debris will naturally accumulate in and around your plunge saw, potentially affecting its performance as it becomes abrasive, causing premature wear. To prevent damage and unnecessary wear, regularly clean the saw body, the depth scale, and other parts using a soft brush, cotton swab, or cloth. Ensure you remove sawdust from the grooves in the guide rail, around the blade, and the dust port. Additionally, clean the cooling vents to prevent overheating. While cleaning is crucial, it's also important to be aware of the cleaning agents and methods that could potentially harm your saw. Avoid using cleaning agents such as those containing ammonia, which may damage the saw. Avoid using compressed air to clean your plunge saw, as it may blow dust and debris into the motor housing. Never underestimate dust damage; even softwood sawdust can affect performance. Once your saw is clean, the next crucial step towards maintaining its efficiency is blade maintenance. The saw blade is the heart of your plunge saw, and proper maintenance is crucial for its performance and longevity. Keep the saw blade clean by removing any resin or pitch build-up after each use. Use a specialised blade cleaning fluid or a mixture of warm water and mild detergent for cleaning. Ensure the blade is dry before reattaching it. Regularly inspect the blade for any signs of damage, such as worn or missing teeth, cracks, or warping. If you notice any issues, replace the blade immediately to avoid compromising safety and ensure quality cuts. Using a professional saw blade sharpening service is essential, as blunt or improperly sharpened blades are inefficient, strain the motor, damage workpieces, and pose safety hazards. Maintain the Plunge Saw Blade Regularly Inspect Your Plunge Saw As part of your maintenance regimen, regularly inspect the power cord, safety features, handles, and knobs for any signs of wear or damage. Ensure all adjustments can be made smoothly and all the safety features are in working order. While using your saw, listen for unusual sounds, and look for reduced cut quality or power. These can all be symptoms of potential problems, and by addressing them early, you can avoid costly repairs and safety hazards.

The guard is jammed on my mitre saw.

How do I fix it? Firstly, disconnect the power, remove the blade and find the material jamming the guard up through the neck of the machine. You can use a Dust Extractor extractor to clean the area. Usually, a larger chip of material has caused the jam, remove the chip, re-attach the blade and power. SEE ALSO: Q: The guard on the KS 120 is not retracting correctly, what can be done to fix?

When cutting with a Festool Circular or Plunge Saw what speed should be use?

This will depend on the application

When setting the depth of cut on my plunge saw there are two indication points - one is blank and one says FS - which one should I be using?

You should use the FS indicator when using the FS Guide Rails, otherwise use the blank indicator is set when not using a rail. The difference between the two indicators is the thickness of the guide rail.

Which Parallel fence guide suit which saws?

The 491469 parallel Side Fence is suitable for the TS 55, and the 576912 parallel side fence is suitable for the HK 55 and the 576912 parallel side fence is suitable fo the HKC 55

Can I use dust extraction when cutting aluminium with my KS120/88/60 or TS 55/60/75?

Yes. Dust extraction can be used when cutting aluminium.

Can I use the cross cut rails for every saw?

No, predominantly the cross cut guide rails are used with the HK saw range. The new TS 60 plunge saw range can also fit onto the FSK rails

My new guide rail has a plastic cover sticking out and I will cut through it when I use my saw.

Is that normal?Yes. It is normal to cut through the splinter guard when you first use the guide rail.

Why are the FSK guide rails not compatible with the TS 55 160 mm Plunge Cut Circular Saw and what is the difference?

The FSK guide rails are not compatible with the TS 55 160 mm plunge saws as their base plates are missing the rebate to lock them in.

Reciprocation Saws

Can I use the RSC18 reciprocating saw on the same setting for all materials?

No - its recommended to use the minimum setting for metal material and maximum for wooden material. Â

Can the RSC 18 saw take non Festool blades?

Yes, the RSC 18 saw uses a standard fitting so other blades are compatible.

Can the RSC Reciprocating Saw be used on concrete?

The RSC 18 18V Cordless Reciprocating Saw is designed for use with wood/steel/plastic/plasterboard and similar materials. Use on concrete may void warranty if the tool is damaged.

Can you get the dust extraction accessory separate for the RSC 18 saw ?

Yes. the dust extraction adapter is vailable seperately. The part number is 577074

Can you remove the guide for close access on the RSC 18 saw ?

Yes, you can remove the guide for close access when required.

Can you use blades upside down in the RSC 18 saw?

Yes. Blades can be fitted upside down in the RSC18.

DUPLICATE - Does the new RSC 18 18V cordless reciprocating saw take competitors blades?

Yes it does take competitors blades even though Festool range a various amount for the saw.

I need to replace the dust extraction nozzle on my RSC 18 Reciprocating Saw?

The replacement part number is #577074

SYMC

Can I use the double extraction for the new SYMC 70 saw?

Yes you can, by using the Y Piece connector for dual suction hoses

Can I use the new SYMC 70 to cut aluminium?

Yes you can by purchasing the Aluminium Saw Blade 210mm x 2.3mm x 30mm 64 Tooth

TS / TSC Saws / TKS SawStop

Can after-market blades be used TKS 80 SawStop?

Only Festool blades are recommended to be used with TKS 80. If an after-market blade is used on the TKS 80, Festool cannot guarantee the effectiveness of the SawStop function.

Can I use the TKS 80 SawStop Saw without the SawStop cartridge?

No, the SawStop feature of the TSK 80 is a vital safety feature of the saw so you will not be able to use your TSK 80 SawStop until the cartridge has been replaced. To have the cartridge replaced contact your nearest Festool Dealer or contact Festool directly through our Repairs Centre

Can 3rd party blades be used on Saw Stop?

Yes, as long ads the specs of the blade are the same same curve thickness and the same diameter.

What capacity is attainable when using the 575827 TKS 80 with sliding table?

A 920mm cross cut can be achieved with the SawStop Sliding 920mm Extension Tables

What is the cutting height on the TKS 80?

The cutting height of the TKS 80 SawStop 254mm Table Saw at 90/45 degrees is 80/56mm.

What material is my TKS 80 table top made of?

Is it aluminum?The tabletop and the portals of the TKS 80 are made of magnesium through-cast.

Why does the TSV 60K Plunge Cut Scoring Saw come with a 1900mm rail and not the standard 1400mm?

As the saw is longer than the others in our range due to the pre score function, the 1900mm rail gives you the room to begin and end the cut off of the material.

Are the guide rail support pads on the baseplate for plunge saws replaceable?

Yes they are. Glide Pads #10679073 for TS 60K Glide Pads #200173 for all other Circular saws are available to order through your closest Festool Dealer

Can a dust bag be attached to the TS 55 REBQ plunge cut saw?

Yes, a dust bag (product number 500393 ) can be attached to the TS 55 REBQ plunge saw. To be able to do this you would need to replace an angle piece on the protective cover. Product number of the angle piece is 202096 - available to order online or from your local dealer.

Can I use the TS/HK tool dust catch bag when cutting aluminium?

The bag is designed for wood dust only, so there is a chance the aluminium may damage it or the bits get stock in the material, so use of the dust catcher bag is at your discretion!

Can I use the TSC 55K with one battery?

Yes, you can use the TSC 55K with one battery, when doing so the single battery must be placed in the top position. Note: When using just one battery the RPM of the saw will reduce to approx 3800 RPM.

Can the TS 55 be fine-tuned if the blade isn't accurate?

Yes. The dial on top of the depth guage allows adjustment to zero the TS 55 blade accurately.

Can the TS 55 F be used with the cross cut rail?

No, the base plate does not have the second groove to enable the saw to fit corly on the rail, however you can use the TS 60K with the cross cut rails

Can the TS 60K be used on the FS and FSk Guide Rail?

Yes, the TS 60K and the TSV 60K can be used on all guiderails in the Festool range.

Can the TS 75 cut melamine 70mm deep?

Yes - the TS 75 210mm Plunge Cut Circular Saw cutting depth is 0mm - 75mm (at 45 degrees the depth is 55mm)

Can TSC 55 blades be sharpened?

Yes, the blades can sharpened up to (approx) 6 times, adjust the cutting edge to 0 point

Do the blades for the TS 55 and TSC 55 also fit the HK 55/HKC 55?

The early versions of the TS55, TSC55 160mm Plunge Cut Saws were delivered with 2.2mm thick blades and don’t work with the existing 1.8mm thick blades. The existing models of TS55 and TSC55, and the HK55 and HKC 55 share the same range of accessories and consumables.

Does Festool have a TS 75 Hebel blade?

Festool does not have a blade that cuts Hebel products. The PCD blades are only designed to cut FC sheet. As Hebel in most cases has reinforcement bars through the panel, the user is required to source a suitable blade for using Festool products when cutting Hebel products.

Does the new TS 60 K connect on to the FSK rails the same way as a HK 55 does?

Yes, they attach, lock-in and are removed in the same way.

How to calibrate a TS 55 / TS 75 on a FS rail ?

Festool saws can be calibrated to the rail by adjusting the green cams on the base plate. Adjusting the cams will take out any movement between base plate and guide rail.

Is using the Dust Catch Bag on my TS 55 or HKC as efficient as using them with dust extration?

A Dust Catch Bag is efficient to 90%, compared with 95% for Dust Extraction (using an attached Dust Extractor). You will also need to empty the Dust Bag quite often (depending on usage) to maintain the dust collecting efficiency of the dust bag.

My new TS 55 / TS 75 will not plunge to the full depth.

Why?Prior to your first cut using your new saw and guide-rail together, the splinter guard on the guide rail must first be trimmed to allow free movemnt of the saw blade as it plunges down in the cut. To do this, you should trim the splinter guard along its full length. Place the saw on the guide rail, turn the saw on and slowly plunge the saw down and run it along the fill length of the rail to finely trim the edge of the splinter guard. This will ensure a zero tolerance cleance against the blade and the guard.

NO Does the TSK 80 have an induction motor or a universal motor?

The TSK 80 has a universal motor and has similar design to the CS 70 motor. In fact it shares some common parts.

Can I set the blade depth on the TS 55 saw and cut without plunging?

No, as there is no blade guard on the TS 55 range it is not possible. The HK range of saws do have a retractable blade guard and are perfect for this application.

Can the saw blade on my TS 55 and TS 60 K be calibrated after it has been sharpened?

The TS saws (TS 55 and TS 60 K ) can be adjusted so the 0 point is accurate but no other adjustments are required.

Can the universal saw blade that comes with the CS 50 (part number 492048) be used with the TS 55 circular saw?

No, the Universal Saw Blade (part number 492048)Â cannot be used on the TS 55 Plunge Saw, the size and centre bore is different (thicker) and it will not fit in the TS 55 series

Does the TS 75 or TS 55 circular saws have a blade that cuts Hebel?

There are 3rd party blades available with the correct centre bore (20mm for TS 55 and 30mm for TS 75) to cut Hebel with a Festool Saw. Some customers choose our saws to use with these blades for better dust extraction and other benefits.

Does the TS/C 55 ABSA (part number 491750) Dust Cover also fit my HK/C 55?

Yes. The Dust Cover for the TS/C 55 (491750) will also fit onto the HK/C 55, However! You will need some extra parts to ensure the correct fit and optimal performance. Hex bolt 402234 Compression spring 444754 Clamp 10012382 Thumb nut 440712

Does the TSV 60 needs to be aligned before you begin using?

Yes, the TSV 60 should be aligned before use to ensure accurate cuts and correct depth.

Does the TSV 60K Plunge Cut Scoring Saw come in a cordless version?

There are no current plans for this to be released in a cordless version

How far can I cut in 12mm material using TSC 55 160mm Cordless Circular Saw?

The total length cutting capacity in 12mm material of a TSC 55 160 mm Cordless Circular Saw is 50 meters. Kitchen worktop 40mm-45-50 lm Pine 40mm (Rip cutting)-15-20 lm Ply 19mm -60-70 lm.

My TS 55 Saw is making strange noises?

The strange noise is caused by MMC electronics in the tachometer regulated speed control sending power to the motor in a stream of various sized bits. The motor is constantly being turned on and off in order to keep the saw blade rotating at a constant speed, most of the sound is being produced by gear backlash this is a normal function with this tool.

Does the TS 55F work with the cross cut rail system?

No, the TS 55 is not compatible with FSK cross cut rails Â

Is the TS 75 EBQ Plus Circular Saw suitable to cut through plaster and soft bricks?

Yes the TS 75 EBQ Plus Circular Saw is able to cut through plaster and soft bricks. BUT: It is a saw made for wood working - that is why warranty can be an issue. When using dust extraction and the appropriate blade matched correctly for the application the TS 75 will be suitable.

On the TS 75 Circular Saw, is the protective material inside the Counter Flange and the Clamping Flange available as spare parts and replaceable?

Yes, the Clamping Flange (part number 492217) and the Counter Flange (part number 492216) are available as spare parts however the protective material between the flange and the blade is bonded to the flange and not available as a stand alone spare part.

REVIEW Can I use dust extraction when cutting steel with my HK 132/85 circular saw or TS 75 plunge saw?

dunno - i think no

REVIEW What capacity can be achieved when using the TKS 80 Table Saw with the 575840 Side extension table?

680mm Rip Cut can be achieved

The cartridge on my TKS 80 was triggered, can I use the saw without the SawStop cartridge until I buy a new one?

The TKS 80 saw cannot be used without the SawStop cartridge.

What does the 1-6 speed setting on the TS 55R EBQ saw mean?

The TS 55R EBQ saw is rated 2000-5200 no load speed and is broken down into 6 speed settings:1 = 2000rpm 2 = 2640rpm 3 = 3280rpm 4 = 3920rpm 5 = 4560rpm 6 = 5200rpm Blade speed is adjustable for cutting materials with most appropriate blade and getting the best quality of cut.

Which guide rail(s) can the TS 60K Plunge Cut Saw go on?

The TS 60K Plunge Cut Saw will fit on both the FS Guide Rails and the FSK Guide Rails

Can I use 1 x 5.0Ah and 1 x 5.2Ah battery with either of my TSC 55 or a CSC SYS saws?

Yes, both the 5.0Ah and 1 x 5.2Ah batteries can be used in combination on the TSC 55 or the CSC SYS 50 saws.

Can i use the FSK rail with the TSC or TS saws?

All TS 55 and TSC 55 plunge saws cannot be used wit the FSK rails.

Can I fine tune for TS 55 if I think the blade isn't accurate?

Yes. There is an adjustment wheel on the top of the depth adjustment that allows calibrating of the zero point to the blade.

Can I fit a dust bag to my old TS 55 or new TS 60?

Yes, the Dust Catch Bag for TSC 55 & HKC 55 (part number 500393) is compatible with all TS 55/60/75 and HK 55/85/132

Can I run a TSC 55 on one 18V battery?

The TSC 55 can be run on one battery however this does limit speed options ( Idling speed (2x18V) 2650-5200 rpm Idling speed (1x18V) 2650-3800 rpm ). Using one battery will also limit the available speed and overall run-time.

Can I sharpen the scribing knife on my TSV 60?

No, this item would need to be re-purchased - item number is 577082

What speed should I run my Festool TS 55/65 on different materials and blades?

As the chart in user manual indicates, use the correct blade and these speed ranges for each type of material: Solid wood (hard, soft) 6 - Chipboard and hardboard 3–6 - Laminated wood, blockboard, veneered and laminated panels 6 - Laminate, mineral materials 4–6 - Plaster- and cement bonded chipboard, and fibreboard 1–3 - Aluminium panels and profiles up to 15 mm 4–6 - Plastics, fibre-reinforced plastics, paper and fabric 3–5 - Acrylic glass 4–5.

Why does the TSV 60 have a green plug-it cable?

The green Plug-It cable is for extra heavy-duty protection against damage due to sharp edges.

Is there a diamond blade for the TS75 available?

Yes, there is a diamond blade for the TS 75 210mm Plunge Cut Circular Saw

TS 55 V HKC 55.

What are the differences? The main differences between these two saws are: TS 55 - Easier to plunge Variable speed - Provides better dust extraction- Has more blade options- Provides splinterguard protection on both sides of the blade. Works more comfortably with the FS Guide rail. Compatible with the CMS Table and Module. HKC 55 - More of a rough cut saw Gives the benefit of being able to be used as a freehand saw - Used on the FSK rails for fast and accurate crosscuts - Can also be used on the standard FS rails with all accessories that are available for the plunge saws.

Can the pre scoring blade that is on the new TSV 60K be retrofitted on to the TS 60K?

No, the TSV 60KÂ is a completely new model with many different and unique parts which means the scoring blade cannot be retrofitted to the TS 60K

Can the protective material on the inside of the TS 75's blade flanges be replaced?

The Clamping Flange and the Counter Flange are available as spare parts however the protective material between the flange and the blade is bonded to the flange and not available as a stand alone spare part. Part numbers: Internal Clamping Flange: 492217Counter Flange: 492216

CMS -TS 75: Can the flange be turned around so a smaller blade (20mm bore) can be used instead of the 30mm bore?

No. The flange cannot be turned around so a smaller blade (20mm bore) can be used instead of the 30 mm bore.

How do I fit the Dust Catch Bag (500393) to my TS 55 or HKC?

Remove the angle piece from the dust port on your TS 55 or HKC 55 and fit the Dust Bag over the opening.

Do you need the same screws for part number 491469 Parallel Side fence in order to use the dust cover 577341?

Yes, you will need the same screws for the dust cover for the TS 55 range