Search
Find a Dealer Near You
My Cart

Edge Banders - Your Questions Answered

Edge Bander Questions - Disclaimer: The information provided on this page is intended for general guidance only and is based on our knowledge at the time of publication. Product specifications, recommendations, and information regarding dust extraction best practices are subject to change without notice. While we strive to keep this information up-to-date, we cannot guarantee its complete accuracy or relevance to your specific circumstances at all times. For the most current and detailed information, please always refer to the official Festool product manuals, data sheets, and local regulations. If you have specific questions, please contact our customer support team directly -> Contact us.

Category
Search for accessories for your tool

Go to Accessories

Can I remove the handle off the KA 65?

Yes, the handle is removable to attach to the table and to store back into the Systainer.

Can the KA 65 CONTURO Edge Bander be used for melamine?

Yes, the KA 65 CONTURO Edge Bander is suitable for all standard materials including melamine. It supports edge heights of 18–65mm and edge thicknesses of 0.5–3.0mm.

Do I need to clean my edge bander CONTURO KA 65?

If using natural glue, cleaning is not necessary. The machine can sit unused for weeks or months with glue inside. Cleaning is only required after using PU adhesive to prevent chemical reactions with the tool.

Does the edging magazine for the KA 65 include a cutter to cut material?

No, the edging magazine does not have a built-in cutter. It is designed for safe guidance of delicate and thin edging into the KA 65.

How can I clean my KA 65 if I use PU glue?

Use the polyurethane rinsing agent after working with PU adhesive to prevent chemical reactions inside the tool. It can be stored for up to 12 months.

How long does it take for the glue to heat up in the KA 65 Conturo Edge Bander?

The glue heats up in approximately 8 minutes, after which the machine is ready to use.

I see there is an attachment for the KA 65 Edge Bander that holds the edging. Can I put the whole roll of edging in here?

The KA 65 Edging Magazine is designed for pre-cut lengths. It does not have a cutting feature and is not intended for full rolls.

Is the KA 65 Plus CONTURO Edge Bander suitable for timber edging?

Yes, it can be used for timber edging. The maximum thickness for timber edging is approximately 0.5mm, depending on the material.

Is there an adjustable stop for the KA-UG?

Yes, an adjustable stop attachment is available for use with the KA-UG left and right trimming attachments for the KAPEX trolley. Part number 234234 attaches to the trimming attachments and can be folded out of the way without removal.

KA 65 Conturo Error code E09 or E10?

These errors indicate a cooling fan issue. Melted glue may block the fan. Try manually turning the fan with a small instrument to clear the error. The fan is located underneath the unit.

What is Festool's correct process for completing mitre edges with the KA 65 edge bander using 22mm tape and a 40-degree angle?

The 5mm plastic spacers may be too high. Festool recommends adjusting the setup based on the tape thickness and angle. For precise guidance, refer to Festool's technical documentation or support.

I am getting an error code no. 9 on my KA 65 edge bander, what does this mean?

Error code 9 usually means the fan underneath is stuck due to glue or debris. Use compressed air or gently clear it with a paper clip.

What degrees is the glue ready to use for the KA 65?

The glue is ready for use when it reaches 190°C.

What does error 7 mean on my KA 65 Edge Bander?

Error 7 indicates a clogged nozzle that isn’t opening properly. It’s easier to clean excess glue around the nozzle lever when it’s hot, as the glue softens and scrapes away more easily.

What does the book icon with error number 9 and 10 mean on the KA 65?

These errors are related to fan issues.

Error 9: Fan in the base

Error 10: Fan near the glue nozzle

Try manually turning the fan with a small object (e.g. straightened paperclip) or blowing compressed air through it to clear debris. If the issue persists, contact Festool service.

What is the standard edge height that can be used on a KA 65?

The standard edge height is 21mm. The full range is 18–65mm in height and 0.5–3.0mm in thickness.

What size edging tape can be used with the CONTURO KA 65 Edge Bander?

The KA 65 supports edging tape with thicknesses from 0.5mm to 3mm and heights from 18mm to 65mm.

When would I need the KA 65 Plus CONTURO Edge Bander adaptor plate vs. the adaptor plate and the perforated top?

Use the adaptor plate alone when building your own table setup.

Use the adaptor plate with the perforated top for angled applications.

Why does the KA 65 Conturo Edge Bander have a dust port?

The dust port is used for fume extraction or cooling the machine.

What colours does the Edge Bander Glue come in?

Available colours include:

Brown (Part number: 200059)

Black (Part number: 200060)

White (Part number: 499813)

Natural (Part number: 499812)

What are the different colour glues that I can buy for Festool Edge Banders?

Glue colours available for the KA 65 include Natural (clear), White, Black, and Brown to match different applications.

How can I keep my material scratch-free when using the edge bander?

Use the scratch-free base pad, which includes a felt layer to protect delicate or high-gloss surfaces.

Create an Account