M Class

M class extractors filter 99.9% of particles and are the correct choice for most Australian trade work.

Hardwood, MDF, plaster, concrete, brick and anything releasing respirable crystalline silica all fall under M class. If you sand, rout, saw or drill any of those, this is the class you need.

Searching for an M class vacuum? This is the right page. M class is a machine rating, not just a filter rating, covering total leakage as well as filtration.

Automatic filter cleaning holds suction through the job. Tool-triggered start means extraction runs only when the tool does. Adjustable suction stops thin material lifting.

For general nuisance dust only, L class is sufficient. For asbestos, lead or mould, you need H class. Full comparison in the L, M and H class guide.

Getting the set-up right for silica ↓

    12 Items

    Set Descending Direction
    per page

    Site dust and silica

    The dust you can see is not the one that hurts you.

    It hangs in the air for hours. Here's how to catch it at the cut.

    • M class is a rating, not a label. It is a whole-machine rating covering total leakage as well as filtration, which is why a shop vac with a fine filter in it is not the same thing.
    • Captured at the blade, not off the floor. A broom moves fine dust around and a workshop vacuum puts it back in the air. Most of the dust is captured at the cut, before it gets into the air.
    • Small enough to actually get used. Extraction that stays in the ute protects nobody.
    Get help with your site dust

    Tell us what you're cutting. We'll recommend the level of protection and the set-up to match, usually within one business day. No charge, no obligation.

    Watch: how to stop losing good workers to dust
    470+authorised Festool dealers across Australia
    10 yearsspare parts held after a tool is discontinued
    ~30 minsa day less clean up when cutting fibre cement with on-tool extraction
    100+years of craft, engineering heritage since 1925

    Five costs of site dust that never make the invoice

    1

    The 10am cut is still in the air at 4pm

    Fine dust stays suspended for hours. The apprentice sweeping up at four o'clock is breathing the cut that happened at ten, and so is every other trade still on the floor. Nobody on the job signed up for that.

    2

    You pay for it twice

    Once in clean up, and again when dust in the frame means a finishing trade goes back over work that was already signed off. Neither of those hours is in the contract price.

    3

    It settles on everything you've finished

    Cutting fibre cement, grinding concrete and sanding render all put grit onto surfaces that are supposed to be done. On occupied sites it also lands on things that belong to the client.

    4

    It's the first thing an inspector asks about

    Silica controls are now standard questioning on site. The best answer is one you can walk an inspector through: dust captured at the tool, and the right respirators on the crew. One doesn't replace the other.

    5

    It goes home with your crew

    Dust on the clothes goes into the ute, then the house. This is the part of the argument that lands with the people who ask the tradesperson to look after themselves.

    Fine dust hanging in the air of a roof space, lit by a skylight, long after the cut that made it
    What the light picks up is the coarse fraction. The particles that reach the lungs are smaller again, and stay airborne for hours.
    Two Festool cordless sanders on a clean bench in a workshop, with no dust on the surface or the floor around them
    The other version of the same day. Nothing to sweep, and nothing settled on work that was already finished.

    80 minutes back on a day of cement sheet cutting

    Twenty cuts of 2.4 m cement sheet, costed at $80 an hour, with a rail saw and M-class extraction against marking out and cutting freehand.

    Where the time goesSaved
    Measuring back and clamping from offset marks3 mins per sheet
    Clean up at the end of the day30 mins
    TotalAbout 80 mins, or $119 a day

    Figures from the Festool cement sheet cutting pain point, measured across the cutting and extraction system rather than any single tool. On fibre cement lining boards the equivalent figure is about 40 mins, or $53 a day, over 40 cuts. Run your own numbers with the Festool Value Calculator.

    Tell us how we can help

    Is your vacuum rated for silica?

    The class on the label is only half the answer. A unit rated M class still has to be working as one on the day: the right filter fitted and seated, the hose and fittings matched to the tool, the filter cleaning doing its job, and the bag changed before suction drops away. Any one of those slipping takes a rated machine below the rating it was bought for. If you are weighing up which class the work needs in the first place, that is set out in the L, M and H class guide.

    Please note: always check with your site safety officer as well, to be sure the site has no special requirements of its own. Some head contractors have been known to specify H class even where M class is rated for the work.

    What's expected of you on silica

    Work health and safety law requires exposure to respirable crystalline silica to be eliminated, or minimised so far as is reasonably practicable. On-tool extraction is one of the recognised control measures. It sits above respiratory protection in the hierarchy of control, and the two are used together.

    The obligations are set out by SafeWork Australia and your state regulator. Penalties for working with silica without the correct set-up run to $30,000.

    No single purchase makes a site compliant. The right extraction class is one part of a documented control plan, alongside assessment, training, monitoring and record keeping. Read the SafeWork Australia guidance.

    A Festool mitre saw on a mobile stand connected to a dust extractor inside a framed house under construction

    “So worth it for my business”

    “Buying the dusty was an investment, but it was so worth it for my business, not only my health and my workers' but also the time saved cleaning up. If you work it over a period of time, it pays for itself.”

    KeithInside Out Renos

    “When working with wood, one of the worst things about each job is the dust. It goes everywhere, it's a nightmare. Particles travel in the air and sit up in the air for a long time. Vacuums are super important for my health and my workers' health.”

    Christian Cole

    From question to the right set-up in three steps

    1. Tell us what you're cutting

    Fill in the form below with the material, how many are on the tools and where the work happens. No charge and no obligation.

    2. Get a written recommendation

    The extraction class and set-up that matches the work, including the parts that have nothing to do with us. Usually back within one business day.

    3. See it on your own material

    A demonstration on site or at your local authorised dealer, so the crew sees the set-up working on the material they actually cut. Request a demo.

    Straight answers before you send it

    Does it cost anything?

    No. The review and the written recommendation are free, and there's no obligation to buy. Whether you buy, and where, is up to you.

    How soon will I hear back?

    Usually within one business day, Monday to Friday, 9am to 4pm AEST.

    What do you need from me?

    What's being cut, how many are on the tools and where the work happens. You don't need a budget or a product in mind.

    Do we still need respirators?

    Yes. Dust captured at the tool and the right respirators on the crew are used together. One doesn't replace the other.

    Can we see it working first?

    Yes. We can arrange a demonstration on site or at your local authorised dealer, on the material your crew actually cuts.

    A tradesperson sanding a plasterboard wall with the sander connected to a Festool AUTOCLEAN extractor, wearing a respirator and eye protection
    On-tool extraction and a respirator. The two controls are used together, and neither replaces the other.

    Get your free site dust review

    Not about the budget. What is being cut, who is on the tools and where the work happens is enough to give you a straight answer.

    Thanks, we've got it. One of our team will be in touch, usually within one business day (Monday to Friday, 9am to 4pm AEST).

    Please enter your first name.

    Please enter your last name.

    Please enter a valid email address.

    Please enter a 10-digit phone number.

    Please enter a 4-digit postcode.

    Please choose your trade.

    Please choose how many are on the tools.

    Please tell us what's making the dust.

    Best way to reach you

    Please choose how you'd like us to reply.

    We use your details to answer this enquiry, and send builder guides and offers only if you tick the box. See our privacy policy. Nothing on this page is legal advice, and no product on its own makes a site compliant. This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

    PS. The short version: tell us what you're cutting and we'll send back the extraction set-up that suits it, usually within one business day, at no charge. Doing nothing costs you the clean-up hours, the call-backs on finished work and the dust your crew takes home. Get your free site dust review.